Mettler Toledo M300 FLOW Dokumentacja Pobierz pdf (Strona 52)

Transmitter M300 FLOW 52

Printed in Switzerland 52 121 319

10.3.3 Proportional Limits

Enter the low and high proportional limits – the range over which control action is required.

Press [ENTER].

10.3.4 Corner Points

Enter the low and high corner points, in ﬂow units, and the respective output values from –1 to

+1, shown in the ﬁgure as –100 to +100% (normally left at the default values for ﬂow).

Pressing the [ENTER] key again will bring up the Save Changes dialog.

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 69 70

Operation Manual 1
Transmitter M300 FLOW 1
Transmitter M300 FLOW 2 2
Transmitter M300 FLOW 4 4
Transmitter M300 FLOW 5 5
Transmitter M300 FLOW 6 6
1 Introduction 7
2 Safety instructions 7
Transmitter M300 FLOW 8 8
3 Unit overview 9
3.2 Overview 1/2DIN 10
3.3 Control/Navigation Keys 11
3.3.2 Navigation keys 12
3.4 Display 13
4 Installation instruction 14
Power Fuse 15
METTLER TOLEDO 17
4.3 Connector PIN deﬁnition 19
Transmitter M300 FLOW 20 20
4.4 Connection of Sensor 21
4.6 Kit Contents 21
Flow Sensors 22
Type: high 22
Racine Federated 26
(formerly Asahi/America) 26
Vortex Sensor 26
5 Placing in/out of service 27
6 Quick Setup 28
6.4 Measurement Selection 29
6.5 Analog Outputs 29
6.6 Set Points 30
7 Calibration 31
7.2 Sensor Calibration 32
7.2.2 Two point Calibration 33
7.3 Edit 34
7.4 Verify 34
8 Conﬁguration 35
8.2 Measurement Setup 36
8.2.1 Set Averaging 37
8.2.2 Set Pipe ID 37
8.2.3 Reset Total Flow 38
8.2.4 External Total Reset 38
8.3 Analog Outputs 39
8.4 Set Points 40
Transmitter M300 FLOW 41 41
8.5 Alarm 42
8.6 Display 43
8.6.3 Backlight 44
8.6.4 Name 44
8.7 Hold Outputs 45
9 System 46
9.3 Passwords 47
9.4 Set/Clear Lockout 48
9.5 Reset 48
Transmitter M300 FLOW 49 49
10 PID Setup 50
10.1 Enter PID Setup 51
10.2 PID Display Auto-Manual 51
10.3 Tune Parameters 51
10.3.3 Proportional Limits 52
10.3.4 Corner Points 52
10.4 Mode 53
10.4.2 PID Control Tuning 54
11 Service 55
11.1.2 Digital Input 56
11.1.3 Display 56
11.1.4 Keypad 56
11.1.5 Memory 56
11.1.6 Set Relays 57
11.1.7 Read Relays 57
11.1.8 Set Analog Outputs 57
11.2 Calibrate 58
11.2.2 Calibrate Analog 59
11.3 Tech Service 60
12 Info 61
13 Maintenance 62
14 Trouble Shooting 63
16 Speciﬁcations 64
Transmitter M300 FLOW 65 65
17 Default Tables 66
Transmitter M300 FLOW 67 67
18 Warranty 68
19 UL Statement 68
Transmitter M300 FLOW 69 69

Komentarze do niniejszej Instrukcji

Brak uwag

Mettler Toledo M300 FLOW Dokumentacja Strona 52

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Mettler Toledo M300 FLOW